First toothy edge

Hello There, Guest! Register

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Thread Modes

First toothy edge

SHARPCO Offline

Offline

Member

Posts: 219
Threads: 65
Joined: Jan 2018

#23

01-30-2019, 01:11 AM

grepper.

I heard that the edge finished with poly diamond compound is better slicer than aluminum oxide compound. So I'll try to finish the edge with 4 micron poly diamond emulsion. I expect to be able to make a pretty aggressive edge with it. Do you think toothy edge is better than this?

Find

Reply

« Next Oldest | Next Newest »

Messages In This Thread

First toothy edge - by SHARPCO - 01-21-2019, 08:49 PM

RE: First toothy edge - by grepper - 01-21-2019, 10:19 PM

RE: First toothy edge - by SHARPCO - 01-21-2019, 10:58 PM

RE: First toothy edge - by grepper - 01-22-2019, 11:00 PM

RE: First toothy edge - by Ken S - 01-23-2019, 12:41 AM

RE: First toothy edge - by SHARPCO - 01-23-2019, 12:54 AM

RE: First toothy edge - by Mike Brubacher - 01-23-2019, 05:18 PM

RE: First toothy edge - by SHARPCO - 01-27-2019, 01:11 AM

RE: First toothy edge - by Mark Reich - 01-28-2019, 06:38 PM

RE: First toothy edge - by SHARPCO - 01-29-2019, 12:20 AM

RE: First toothy edge - by Mark Reich - 01-27-2019, 07:49 PM

RE: First toothy edge - by SHARPCO - 01-27-2019, 08:37 PM

RE: First toothy edge - by Mark Reich - 01-28-2019, 11:25 AM

RE: First toothy edge - by SHARPCO - 01-29-2019, 12:14 AM

RE: First toothy edge - by grepper - 01-28-2019, 07:47 PM

RE: First toothy edge - by SHARPCO - 01-29-2019, 12:36 AM

RE: First toothy edge - by Bud - 01-28-2019, 10:27 PM

RE: First toothy edge - by grepper - 01-28-2019, 10:50 PM

RE: First toothy edge - by Mark Reich - 01-28-2019, 11:21 PM

RE: First toothy edge - by Mike Brubacher - 01-29-2019, 12:17 PM

RE: First toothy edge - by Mark Reich - 01-29-2019, 03:17 PM

RE: First toothy edge - by grepper - 01-29-2019, 11:04 PM

RE: First toothy edge - by SHARPCO - 01-30-2019, 01:11 AM

RE: First toothy edge - by grepper - 01-30-2019, 11:09 PM

RE: First toothy edge - by SHARPCO - 01-31-2019, 01:23 AM

RE: First toothy edge - by grepper - 01-31-2019, 05:15 PM

RE: First toothy edge - by SHARPCO - 01-31-2019, 05:49 PM

RE: First toothy edge - by Mark Reich - 02-01-2019, 01:09 PM

RE: First toothy edge - by grepper - 02-01-2019, 05:03 PM

RE: First toothy edge - by SHARPCO - 02-01-2019, 08:22 PM

RE: First toothy edge - by Mark Reich - 02-02-2019, 08:25 PM

RE: First toothy edge - by SHARPCO - 02-02-2019, 10:10 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)