The BESS Exchange is sponsored by Edge On Up › BESS Forums › All About Edges v
First toothy edge

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Thread Modes
First toothy edge
SHARPCO Offline
Member
***
Posts: 219
Threads: 65
Joined: Jan 2018
#17
01-29-2019, 12:14 AM
(01-28-2019, 11:25 AM)Mark Reich Wrote: No worries Mr Sharpco. What is your progression to the polished edge?

My polished edge is quite good. But I'm not proud of it, so I'm considering how to finish it.
Find
Reply


Messages In This Thread
First toothy edge - by SHARPCO - 01-21-2019, 08:49 PM
RE: First toothy edge - by grepper - 01-21-2019, 10:19 PM
RE: First toothy edge - by SHARPCO - 01-21-2019, 10:58 PM
RE: First toothy edge - by grepper - 01-22-2019, 11:00 PM
RE: First toothy edge - by Ken S - 01-23-2019, 12:41 AM
RE: First toothy edge - by SHARPCO - 01-23-2019, 12:54 AM
RE: First toothy edge - by Mike Brubacher - 01-23-2019, 05:18 PM
RE: First toothy edge - by SHARPCO - 01-27-2019, 01:11 AM
RE: First toothy edge - by Mark Reich - 01-28-2019, 06:38 PM
RE: First toothy edge - by SHARPCO - 01-29-2019, 12:20 AM
RE: First toothy edge - by Mark Reich - 01-27-2019, 07:49 PM
RE: First toothy edge - by SHARPCO - 01-27-2019, 08:37 PM
RE: First toothy edge - by Mark Reich - 01-28-2019, 11:25 AM
RE: First toothy edge - by SHARPCO - 01-29-2019, 12:14 AM
RE: First toothy edge - by grepper - 01-28-2019, 07:47 PM
RE: First toothy edge - by SHARPCO - 01-29-2019, 12:36 AM
RE: First toothy edge - by Bud - 01-28-2019, 10:27 PM
RE: First toothy edge - by grepper - 01-28-2019, 10:50 PM
RE: First toothy edge - by Mark Reich - 01-28-2019, 11:21 PM
RE: First toothy edge - by Mike Brubacher - 01-29-2019, 12:17 PM
RE: First toothy edge - by Mark Reich - 01-29-2019, 03:17 PM
RE: First toothy edge - by grepper - 01-29-2019, 11:04 PM
RE: First toothy edge - by SHARPCO - 01-30-2019, 01:11 AM
RE: First toothy edge - by grepper - 01-30-2019, 11:09 PM
RE: First toothy edge - by SHARPCO - 01-31-2019, 01:23 AM
RE: First toothy edge - by grepper - 01-31-2019, 05:15 PM
RE: First toothy edge - by SHARPCO - 01-31-2019, 05:49 PM
RE: First toothy edge - by Mark Reich - 02-01-2019, 01:09 PM
RE: First toothy edge - by grepper - 02-01-2019, 05:03 PM
RE: First toothy edge - by SHARPCO - 02-01-2019, 08:22 PM
RE: First toothy edge - by Mark Reich - 02-02-2019, 08:25 PM
RE: First toothy edge - by SHARPCO - 02-02-2019, 10:10 PM

Forum Jump:


Users browsing this thread: 3 Guest(s)