First toothy edge

Hello There, Guest! Register

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Thread Modes

First toothy edge

Mark Reich Offline

Offline

Moderator

Posts: 592
Threads: 26
Joined: Mar 2017
Reputation: 0

#16

01-28-2019, 11:21 PM

Mr Grepper, have you experimented rolling your toothy edges compared to the very same edge, just taken to higher refinement?

Most people think refined edges are more stable than toothy edges. It makes sense, but I'd really like to know if that holds water.

Reply

« Next Oldest | Next Newest »

Messages In This Thread

First toothy edge - by SHARPCO - 01-21-2019, 08:49 PM

RE: First toothy edge - by grepper - 01-21-2019, 10:19 PM

RE: First toothy edge - by SHARPCO - 01-21-2019, 10:58 PM

RE: First toothy edge - by grepper - 01-22-2019, 11:00 PM

RE: First toothy edge - by Ken S - 01-23-2019, 12:41 AM

RE: First toothy edge - by SHARPCO - 01-23-2019, 12:54 AM

RE: First toothy edge - by Mike Brubacher - 01-23-2019, 05:18 PM

RE: First toothy edge - by SHARPCO - 01-27-2019, 01:11 AM

RE: First toothy edge - by Mark Reich - 01-28-2019, 06:38 PM

RE: First toothy edge - by SHARPCO - 01-29-2019, 12:20 AM

RE: First toothy edge - by Mark Reich - 01-27-2019, 07:49 PM

RE: First toothy edge - by SHARPCO - 01-27-2019, 08:37 PM

RE: First toothy edge - by Mark Reich - 01-28-2019, 11:25 AM

RE: First toothy edge - by SHARPCO - 01-29-2019, 12:14 AM

RE: First toothy edge - by grepper - 01-28-2019, 07:47 PM

RE: First toothy edge - by SHARPCO - 01-29-2019, 12:36 AM

RE: First toothy edge - by Bud - 01-28-2019, 10:27 PM

RE: First toothy edge - by grepper - 01-28-2019, 10:50 PM

RE: First toothy edge - by Mark Reich - 01-28-2019, 11:21 PM

RE: First toothy edge - by Mike Brubacher - 01-29-2019, 12:17 PM

RE: First toothy edge - by Mark Reich - 01-29-2019, 03:17 PM

RE: First toothy edge - by grepper - 01-29-2019, 11:04 PM

RE: First toothy edge - by SHARPCO - 01-30-2019, 01:11 AM

RE: First toothy edge - by grepper - 01-30-2019, 11:09 PM

RE: First toothy edge - by SHARPCO - 01-31-2019, 01:23 AM

RE: First toothy edge - by grepper - 01-31-2019, 05:15 PM

RE: First toothy edge - by SHARPCO - 01-31-2019, 05:49 PM

RE: First toothy edge - by Mark Reich - 02-01-2019, 01:09 PM

RE: First toothy edge - by grepper - 02-01-2019, 05:03 PM

RE: First toothy edge - by SHARPCO - 02-01-2019, 08:22 PM

RE: First toothy edge - by Mark Reich - 02-02-2019, 08:25 PM

RE: First toothy edge - by SHARPCO - 02-02-2019, 10:10 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)