Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
First toothy edge
#9
Whoa! Geez. Sorry I'm late to the party.

Seems like you gentlemen are only showing the One side of the blade that has the burr- with the flimsy burr still attached in the first pictures.

I didn't think the LOW was a burr with a clean leather finish, but I finish on stones, so it looks different to me.

If you gentlemen could please take pictures of both sides of the blade, just like you're taking pictures of one side, it will show what I mean.
Reply


Messages In This Thread
First toothy edge - by SHARPCO - 01-21-2019, 08:49 PM
RE: First toothy edge - by grepper - 01-21-2019, 10:19 PM
RE: First toothy edge - by SHARPCO - 01-21-2019, 10:58 PM
RE: First toothy edge - by grepper - 01-22-2019, 11:00 PM
RE: First toothy edge - by Ken S - 01-23-2019, 12:41 AM
RE: First toothy edge - by SHARPCO - 01-23-2019, 12:54 AM
RE: First toothy edge - by Mike Brubacher - 01-23-2019, 05:18 PM
RE: First toothy edge - by SHARPCO - 01-27-2019, 01:11 AM
RE: First toothy edge - by Mark Reich - 01-28-2019, 06:38 PM
RE: First toothy edge - by SHARPCO - 01-29-2019, 12:20 AM
RE: First toothy edge - by Mark Reich - 01-27-2019, 07:49 PM
RE: First toothy edge - by SHARPCO - 01-27-2019, 08:37 PM
RE: First toothy edge - by Mark Reich - 01-28-2019, 11:25 AM
RE: First toothy edge - by SHARPCO - 01-29-2019, 12:14 AM
RE: First toothy edge - by grepper - 01-28-2019, 07:47 PM
RE: First toothy edge - by SHARPCO - 01-29-2019, 12:36 AM
RE: First toothy edge - by Bud - 01-28-2019, 10:27 PM
RE: First toothy edge - by grepper - 01-28-2019, 10:50 PM
RE: First toothy edge - by Mark Reich - 01-28-2019, 11:21 PM
RE: First toothy edge - by Mike Brubacher - 01-29-2019, 12:17 PM
RE: First toothy edge - by Mark Reich - 01-29-2019, 03:17 PM
RE: First toothy edge - by grepper - 01-29-2019, 11:04 PM
RE: First toothy edge - by SHARPCO - 01-30-2019, 01:11 AM
RE: First toothy edge - by grepper - 01-30-2019, 11:09 PM
RE: First toothy edge - by SHARPCO - 01-31-2019, 01:23 AM
RE: First toothy edge - by grepper - 01-31-2019, 05:15 PM
RE: First toothy edge - by SHARPCO - 01-31-2019, 05:49 PM
RE: First toothy edge - by Mark Reich - 02-01-2019, 01:09 PM
RE: First toothy edge - by grepper - 02-01-2019, 05:03 PM
RE: First toothy edge - by SHARPCO - 02-01-2019, 08:22 PM
RE: First toothy edge - by Mark Reich - 02-02-2019, 08:25 PM
RE: First toothy edge - by SHARPCO - 02-02-2019, 10:10 PM

Forum Jump:


Users browsing this thread: 3 Guest(s)