The BESS Exchange is sponsored by Edge On Up › BESS Forums › BESS v
Thinness of the edge apex

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Thread Modes
Thinness of the edge apex
KnifeGrinders Offline
Knife Grinders
***
Posts: 287
Threads: 34
Joined: Oct 2017
#17
11-05-2017, 04:57 PM
Then shouldn't the dull end be cut off at where it is not linear any more?
1000 BESS or 1 micron edge is a good candidate.
http://knifeGrinders.com.au
Website Find
Reply


Messages In This Thread
Thinness of the edge apex - by Jan - 10-24-2017, 02:00 PM
RE: Thinness of the edge apex - by EOU - 10-24-2017, 02:39 PM
RE: Thinness of the edge apex - by Jan - 10-25-2017, 04:02 AM
RE: Thinness of the edge apex - by EOU - 10-25-2017, 10:13 AM
RE: Thinness of the edge apex - by Jan - 10-25-2017, 02:45 PM
RE: Thinness of the edge apex - by EOU - 10-26-2017, 09:55 AM
RE: Thinness of the edge apex - by KnifeGrinders - 11-01-2017, 03:08 AM
RE: Thinness of the edge apex - by Jan - 11-01-2017, 09:48 AM
RE: Thinness of the edge apex - by KnifeGrinders - 11-01-2017, 02:40 PM
RE: Thinness of the edge apex - by EOU - 11-03-2017, 01:34 PM
RE: Thinness of the edge apex - by admin - 11-03-2017, 07:10 PM
RE: Thinness of the edge apex - by KnifeGrinders - 11-03-2017, 07:23 PM
RE: Thinness of the edge apex - by Jan - 11-04-2017, 03:07 AM
RE: Thinness of the edge apex - by KnifeGrinders - 11-04-2017, 10:59 AM
RE: Thinness of the edge apex - by Jan - 11-05-2017, 06:22 AM
RE: Thinness of the edge apex - by EOU - 11-04-2017, 11:26 AM
RE: Thinness of the edge apex - by KnifeGrinders - 11-05-2017, 04:57 PM
RE: Thinness of the edge apex - by Jan - 11-06-2017, 02:05 AM
RE: Thinness of the edge apex - by EOU - 11-06-2017, 11:11 AM
RE: Thinness of the edge apex - by grepper - 11-06-2017, 02:13 PM
RE: Thinness of the edge apex - by Jan - 11-06-2017, 03:37 PM
RE: Thinness of the edge apex - by EOU - 11-06-2017, 04:41 PM
RE: Thinness of the edge apex - by Mark Reich - 11-06-2017, 06:18 PM
RE: Thinness of the edge apex - by EOU - 11-06-2017, 06:34 PM
RE: Thinness of the edge apex - by Jan - 11-07-2017, 05:26 AM
RE: Thinness of the edge apex - by EOU - 11-07-2017, 11:01 AM
RE: Thinness of the edge apex - by Mark Reich - 11-08-2017, 08:54 PM

Forum Jump:


Users browsing this thread: 5 Guest(s)